Pastebin

New Paste Add Image

[mcu eboard]
serial: /dev/ttyS1
baud: 230400
restart_method: command

[mcu]
serial: /dev/ttyS5
baud: 230400
restart_method: command

[stepper_x]
step_pin: PC1
dir_pin: PC0
enable_pin: !PA1
microsteps: 16
rotation_distance: 40
endstop_pin: !eboard:PA15
#endstop_pin: tmc2209_stepper_x:virtual_endstop
position_endstop: 200
position_max: 200
position_min: 0  # Nozzle içeride kalması için eksiye düşürüldü
homing_speed: 30
homing_retract_dist: 5
homing_retract_speed: 25
second_homing_speed: 5

[stepper_y]
step_pin: PA3
dir_pin: PA2
enable_pin: !PA6
microsteps: 16
rotation_distance: 40
endstop_pin: !eboard:PB11
#endstop_pin: tmc2209_stepper_y:virtual_endstop
position_endstop: 197
position_max: 197
position_min: 0  # Y için de küçük bir negatif değer verildi
homing_speed: 30
homing_retract_dist: 5
homing_retract_speed: 25
second_homing_speed: 5

[stepper_z]
step_pin: PC4
dir_pin: PA7
enable_pin: !PB1
microsteps: 16
rotation_distance: 8
endstop_pin: PB15
#endstop_pin: probe:z_virtual_endstop
position_endstop: 216.415
position_max: 230
position_min: -10
homing_speed:25
homing_retract_dist: 5
homing_retract_speed: 12.5
second_homing_speed: 5

# [extruder]
# step_pin: eboard:PB14
# dir_pin: !eboard:PB15
# enable_pin: !eboard:PB12
# microsteps: 16
# nozzle_diameter: 0.400
# filament_diameter: 1.750
# heater_pin: eboard:PA8
# sensor_type: Generic 3950
# sensor_pin: eboard:PA0
# min_temp: -100
# max_temp: 350
# pressure_advance:0.035
# pressure_advance_smooth_time: 0.040
# max_extrude_only_distance:1500.00
# max_extrude_cross_section:1000

[heater_bed]
heater_pin: PB9
sensor_type: Generic 3950
sensor_pin: PC3
pullup_resistor: 4700
#control: watermark
#max_power: 1.0
min_temp: -100
max_temp: 130

# [verify_heater extruder]
# max_error: 290
# check_gain_time:200
# hysteresis: 10
# heating_gain: 10

[verify_heater heater_bed]
max_error: 120
check_gain_time:200
hysteresis: 10
heating_gain: 10

[led chamber_led]                                                   
white_pin: PA8                                                  
hardware_pwm: False
initial_white: 0.8

# [heater_fan hotend_fan]
# pin: eboard:PB4
# max_power: 1.0
# #kick_start_time: 0.5
# heater: extruder
# heater_temp: 50.0

# [fan]
# pin: eboard:PB5

[fan_generic chamber_fan]
pin:PC6
hardware_pwm:True
enable_pin:PC7

[controller_fan stepper_driver_fan]
pin:PB7
stepper: stepper_x, stepper_y, stepper_z
fan_speed: 0.8
idle_timeout: 0

[fan_generic internal_fan]
pin:PB6

[fan_generic external_fan]
pin:PB8

# unclear what the "power" pins do at the moment
# disable them in the UI for now
[gcode_button btn_power]
pin: !PC15
press_gcode:
    _SHUTDOWN_BUTTON_TRIGGER

[output_pin _power_off]
pin: PC14
value: 1
shutdown_value: 1

[output_pin _clear_power_off]
pin: PG1
value: 0
shutdown_value: 0

[adxl345]
cs_pin: eboard:PA4
spi_speed: 1000000
#spi_bus: spi3
spi_software_sclk_pin: eboard:PA5
spi_software_mosi_pin: eboard:PA7
spi_software_miso_pin: eboard:PA6
axes_map:  x, y, z
rate: 800

[resonance_tester]
accel_chip:adxl345
min_freq: 5
max_freq: 100
probe_points:
        100,100,100

[idle_timeout]
timeout:600

[pause_resume]
recover_velocity: 50

[printer]
kinematics: corexy
max_velocity: 300
max_accel: 3000
#max_accel_to_decel:
max_z_velocity: 15
max_z_accel: 150
square_corner_velocity: 5.0

[tmc2209 stepper_x]
uart_pin: PC2
interpolate:True
run_current: 0.9
#hold_current:0.3
sense_resistor:0.10
#stealthchop_threshold: 12000

[tmc2209 stepper_y]
uart_pin: PA4
interpolate:True
run_current: 0.9
#hold_current:0.3
sense_resistor:0.10
#stealthchop_threshold: 12000

[tmc2209 stepper_z]
uart_pin: PC5
interpolate:True
run_current: 0.6
hold_current:0.6
sense_resistor:0.10
#stealthchop_threshold: 999999

# [tmc2209 extruder]
# uart_pin: eboard:PB10
# interpolate:True
# run_current: 0.8
# hold_current:0.8
# sense_resistor:0.10
# #stealthchop_threshold: 999999

[temperature_sensor Load_Cell]
sensor_type: MAX31856
sensor_pin: PD5
#spi_bus: spi4
spi_speed: 1000000
spi_software_sclk_pin: PD6
spi_software_mosi_pin: PD7
spi_software_miso_pin: PD8
min_temp: 0
max_temp: 2048
gcode_id: W

[temperature_sensor TVOC_Level]
sensor_type: MAX31865
sensor_pin: PD4
#spi_bus: spi4
#cs_pin: PD0
spi_speed: 500000
spi_software_sclk_pin: PE3
spi_software_mosi_pin: PE4
spi_software_miso_pin: PE5
min_temp: 0
max_temp: 2048
gcode_id: V

# reset the check_level_pin state
[output_pin _level_clear]
pin: PD10
value:0

# check level pin is triggered when load cell tare is set via level_h1 pin
[gcode_button _check_level_pin]
pin: !PE0
press_gcode:
    G4 P0

# set load cell tare
[output_pin _level_h1]
pin:PG2
value:0

# don't use (!) - changes load cell calibration
[output_pin _level_h2]
pin:PG3
value:0

# don't use (!) - changes load cell calibration
[output_pin _level_h3]
pin:PG4
value:0

# Unused Filament runout sensor e1 must be configure as an input pint 
# Otherwise the runout sensor does not work
[gcode_button _e1_sensor_input]
pin: !PE1
press_gcode:
    G4 P0

# Filament runout sensor
[filament_switch_sensor runout_sensor]
pause_on_runout: False
switch_pin: !PB14
event_delay: 1.0
runout_gcode:
    _FILAMENT_RUNOUT_EVENT

# [servo my_servo]
# pin:PC9
# maximum_servo_angle: 180
# minimum_pulse_width: 0.0005
# maximum_pulse_width: 0.0025
# initial_angle:95
# #initial_pulse_width:

[gcode_arcs]
resolution: 1.0

[firmware_retraction]
retract_length: 0.8
retract_speed: 35
unretract_extra_length: 0
unretract_speed: 35
  
[virtual_sdcard]
path: /root/printer_data/gcodes
on_error_gcode: CANCEL_PRINT

[display_status]

[exclude_object]

# Home Axis in order Z, X, Y
# Move away from endstop to prevent damage to plastic tab in bed corner
# if bed is raised to nozzle and don't keep head or bed pressed
# against endstop for long time
[homing_override]
gcode:
    # Limit acceleration for homing and moves on print start
    M204 S5000
    G28 Z0
    G28 X0
    G28 Y0
    G90
    G1 X105 Y105 Z210 F1800

# #AutoCalibration                   
# [bed_mesh]                         
# speed: 300                          
# horizontal_move_z:2
# move_check_distance: 5
# mesh_min: -105, -105            
# mesh_max: 105, 105             
# probe_count: 5, 5                  
# mesh_pps: 3, 3                     
# algorithm: bicubic                 
# bicubic_tension: 0.2               
# #fade_start: 3
# #fade_end: 10
# #fade_target: 0

[skew_correction]
                                  
[probe]
pin: !PB4
speed: 2
lift_speed: 5
samples: 1
z_offset: 214.0

Settings

Title : [Optional]

Paste Folder : [Optional]

Syntax : [Optional]

Expiration : [Optional]

Status : [Optional]

Password : [Optional]

Description: [Optional]

Tags: [Optional]

Encrypt Paste (?)

You are currently not logged in, this means you can not edit or delete anything you paste. Sign Up or Login

Settings

Site Languages